Rubber or Plastic Mills

Bolling 28" x 100": 500 HP hydraulically driven mill with hydraulic roll adjusters and drilled rolls                       
Stewart Bolling 26 x 84 Twin Mill:Twin 26” x 84” mill, Both mills have triple pass drilled front rolls. Direct connected via Lufkin T720B 83.5 to 1 reducer, overhead blender, 4 piece base

Adamson United 26 x 84 Dual Drive Mill: 26” x 84” rubber mill,  plastic mill, with individual drives, drilled rolls, 500hp, each roll driven via right angle 64.69 Lufkin reducers, 2-250hp Reliance DC motors, overhead blender, motorized roll adjusters, flip up guides, water cooled bearing housings, 3 piece base

Stewart Bolling 26 x 84 Rubber Mill: 26” x 84” direct connected. Lufkin T540 gear reducer, 300 hp, rebuilt to your specifications   Photo

Bolling 22 x 60 Mill: 22" x 60" left hand drive, 150hp, Falk reducer, with air brake

Farrel 22 x 60 Rubber Mill: 22" x 60" left hand drive, 150 hp, Falk reducer, with air brake

Farrel 22 x 60 Rubber Mill: 22” x 60” Direct connected and unitized, left hand drive, 2 piece keyed base, 200 hp motor

Farrel 16 x 42 Rubber Mill: 16" x 42" unitized and direct connected, no motor

Kobe 16 x 42 Rubber Mill: 16" x 42" 60 hp, pneumatic flip guides, unitized,  no motor

Eemco 6 x 15 Rubber Mill: 6" x 15" Compact cabinet design, 15 hp motor Photo

TMP 6 x 13 Rubber Mill: 6” x 13” Compact cabinet design “ROLLER BEARINGS” 7 ½ hp, ready to go

Farrel 3 x 7 Rubber Mill: 3” x 7” Cabinet design lab mill. Variable speed and variable friction. Each roll driven by a 1 ½ hp variable speed motor. “ROLLER BEARINGS”. 700 degree operating temp. Ready to go.

"New" RME lab and production mills. All sizes up to 16" to 42". Built to your specification.

Extruders

New SK Extruder:   1” and 1 ½” rubber or silicone 20/1 L/D   Photo

NRM Extruder:   2 ½” 12/1 L/D   Photo

NRM Extruder: 3 ½” 12/1 L/D Plastiscrew, 75 hp dc   Photo

Davis Standard Extruder:   3 ½” 20/1 L/D

Troester Extruder:   3 ½” pin barrel   Photo

Davis Standard Extruder:   4 ½” 10/1 L/D   Photo

Davis Standard Extruder:   4 ½” 20/1 L/D   Photo

NRM Extruder:   4 ½” 12/1 L/D   Photo

NRM Extruder:   4 ½” 17/1 L/D Vented   Photo

Davis Standard Extruder:   6” 20/1 L/D   Photo

Monsanto Extruder: 8” 18/1 L/D Vented   Photo

Calenders

Adamson Calender:   30" x 80” 4-roll "Z" calender. drilled rolls, roller bearings, cross axis, single pinion stand with 4 individual reducers.

Farrel Calender: 28" x 74" 4-roll, inverted "L" drilled rolls

Adamson Calender: 24” x 68” 3-roll , 3 drill with offset top roll, 3 new drilled rolls, new roller bearings, individual drives, motorized roll adjusters

Erie 18" x 48" 2-roll Calender, vertical, roller bearings, complete with 6 cooling drums

Gear Reducers

Falk Gear Reducer: 2185YN3-B,  76.92 to 1 ratio rated for 300 HP with a 1.5 service factor, dual inputs and output shafts, airbrake installed

Lufkin Gear Reducer: THB440 CH right angle, 64.69 to1 ratio, rated for 250 hp with a 1.68 service factor, two in stock

Lufkin Gear Reducer: T540AH. 50.70 to 1 ratio. 300 hp with a 1.5 service factor Photo

Lufkin Gear Reducer: T540H 58.3 to1 ration, 200 hp, 1.5 service factor, air brake installed

Lufkin Gear Reducer: T390S 62.8 to 1 ratio, 150 hp, 1.5 service factor, air rake installed

Lufkin Gear Reducer: T390 62.7 to 1 ratio, 150 hp, 1.5 service factor, air brake installed

Hydraulic Presses

Panstone Model S-V-400-2RT-PCD Vacuum Press

Bale Cutters

Used RCM 32" on stand with light curtains both sides, ready to go

Rotocures

Adamson Rotocure:   2 available, 80” oil heated drums, electric heaters, dual band, available for immediate delivery   Photo

Berstorff Rotocure:   60” steam heated drum, electric heaters, dual band, available for immediate delivery   Photo   

Mill Rolls and Calender Rolls

Rolls:

In Stock:

1 Set Kobe 16 "x 42 "mill rolls, front and rear

2 New 16" x 42"  front and rear cored rolls for a Bolling mill

3 New 24" x 68" drilled, roller bearing, calender rolls

1 26" x 84" drilled drive roll for Stewart Bolling mills

2 26" x 84" mill roll assemblies

1 26" x 84" front cored roll

New and used mill and calender rolls 6" x 12" up to 32" X 100"

New and used cored and "drilled" mill and calender rolls. Available in all sizes.

Spare Parts and Miscellaneous 

Midlands 20" cantilever batchoff machine, new in 2004, can be seen operating

Budzar 100 ton chiller, new in 2004, can be seen operating

New bronze bearings in stock for mills and calenders

New screw and nut assemblies for mills

New hydraulic retrofit roll adjusters for mills and calenders

New breaker caps for all size mills

Stock guides for Stewart Bolling mills

Spare bearing housings for 60" and 84" mills